w-u-2-o wrote:Are you really still using PowerSDR? Why not Thetis?

In either case, selecting the "extended" option for the region setting should allow operation in the manner you want.

Hi all ,
I use both , I'm going to check that , tnx
73
Dom

Hello , I am using my ANAN10 as an IF for 23cm. 28>30=1296>1298. I am not using the transverter bands but really the normal 28Mhz TX/RX output. Soon , because of Galileo , we will have to migrate to 1298>1300. At the moment , it is not possible with anan10/powersdr to TX from 30>32. I understand the...

Ok tnx for the information. Abt remote , I've tried with Anydesk , it was close to work , I've only failed to get microphone audio routed to the anan , but maybe I will try harder. One thing not so fine with this solution is to have a pc constantely runing while I am away but I have not tried yet th...

Ok , tnx, pity, it is something very important nowadays.I suppose the problem comes from the way the network behaviour is done in the anan firmware?
73
Dom

Hello , after using openhpsdr mrx for a long time and being quite satified with it , I still had a regret : WAN remote was not working for me. Yesterday I've installed the latest version of Thetis ( protocol1 here) , and started to look at the various configuration menus. Big surprise , there is som...

ok , good information , tnx

Hi all , question : is it OK to have in the same computer Thetis and powersdrmrx ? I would like to test Thetis with my ANAN10 (protocol1) but would not like to uninstal hpsdr just in case it is not working well with Thetis? As far one knows..In case Thetis is ok on my ANAN , I could then switch to p...

Hi all , question : is it OK to get Thetis and HPSDR both installed on a PC and sometimes run Thetis , sometimes run hpsdr? Actually I run only HPSDR but there is someting boring : depending how I use it , I need the setup to be different so I need to modify manually every time. So different softwar...

Hi all agn , could sort my tx problem : it was a small connector routing the tx signal from the Hermes to the amplifier which was disconnected. Now more serious. My ANAN is worse that PA5Y , IMD is -21 relative to one tone on the 3rd order and -33 on the 5th order (at 9W pep). I find it is another b...

Hi guys , not sorted of the pa problem. After firmware and software upgrade , I get the rigth power out of the Hermes , but no power at all out of the 10w amp. I can hear a relay click when I press TUNE but no power out. I reviewed all the software configuration and all looks ok. I will carry on wor...

Hi all agn , I've measured today the IMD on 28Mhz on the low power output with PA disabled. I get the same numbers than PA5Y. I could not do the measurement with the power amplifier as I have a problem there : no more output since I have upgraded to a new firmware and a new HPSDR yesterday. Will do ...

Hi all , I don't know about Conrad , but in my case: I am a V/U/Shfer. The anan is used as a IF , with some power out because all my transverters are far away from the shack. There are several bands using antenna 1 and this antenna 1 port is switched on 13/6/3cm transverters. Antenna 2 goes on the 2...

Hi all ,

sorry to say , but it is not because pure signal improves IMD that the PA can be that bad without pure signal. Maybe quiescent current is wrong?

73
Dom

Hi , me agn , I had a look at the 9744 datasheet. The sfdr explains the spurs we see. Probably my anan is a 10E , I don't know if it is the same ADC in this version , maybe the sfdr is 10dB worse? Anyway , if it is the case , there is no simple way to improve this. I also had a look at the filter , ...

Hi again , I got some time yesterday to run more measurements. You are rigth , spur content depends on sampling. With 384K spurs are -72 (10dB better) , still not enougth and worse than Conrad anan10. A strong signal on the band is something like -30dBm in the offended receiver , then we get 4 inban...

Hello Walter , in fact I don't care abt 2Mhz spurs ( which are probably coming from the 5V switching power supply).I saw them but was not choked. My problem is in band spurs. Your spectrogram has been made on 2m , so imagine someone using such a poor tx during a major european contest with 60dBm or ...

ooooops anan10 not anan 100 like mistyped

Hi all , I saw this topic development on the forum. Should I conclude that all ANAN100are not the same? Mine is bad , generating 4 (at least) in band spurriis in the 28Mhz band and in all bands in fact. It is not a spectrum analyser problem as , to be sure , I used an RX to confirm . These products ...